Table of Contents
Default Password and IP Address Settings for Dahua DVRs
Resetting and Retrieving Passwords on Dahua Camera
Resetting Dahua DVRs using the Reset Button
Configuring Audio Settings on Dahua DVRs
Default Password and IP Address Settings for Dahua DVRs
When it comes to Dahua DVR, the default password can be different depending on the model and firmware version. By default the IP address of the device is 192.168.1.108. If you want to change the IP address, you can utilize the “ConfigTool” tool available for download on Dahua’s official website. This tool enables you to search or modify the IP address of your DVR easily.
Resetting Dahua DVRs using the Reset Button
Dahua DVRs usually come equipped with a reset button that can be incredibly useful in certain situations. The reset button is usually a small hole that can be found on the DVR’s circuit board. This button can be used to reset the DVR to its default settings or to clear any configuration settings, including the password. To use the reset button, you will need to turn off the DVR, insert a paper clip or similar object into the hole, and hold the button down while you reconnect the power to the device. By following these steps, you should be able to reset your Dahua DVR with ease.
- Locate the reset button: The reset button is usually a small hole located on the circuit board of the DVR. It may be labeled “RESET” or “RESE”.
- Power off the DVR: Make sure the DVR is powered off before attempting to use the reset button.
- Insert a paper clip or similar object: Straighten a paper clip or similar object and insert it into the reset hole.
- Press and hold the button: Hold the reset button down using the paper clip while you reconnect the power to the DVR.
- Wait for the reset: Continue holding the reset button for around 10 to 15 seconds until you see the DVR lights start to flash. This indicates that the reset has been successful.
- Release the button: Once the lights stop flashing, release the reset button.
After following these steps, your Dahua DVR should be reset to its default settings. Note that this will also clear any configuration settings, including the password, so you will need to set it up again after the reset.
Resetting and Retrieving Passwords on Dahua Camera
1. You can retrieve the password through the mailbox bound to the DVR, click Forgot Password on the NVR interface to enter the password retrieval QR code interface, download DMSS or imou Life APP on your mobile phone, enter the tool management option, and scan the QR code of the NVR in the password recovery menu code, you can get the unlock password in the bound mailbox.
2. When the NVR is powered off, press and hold the reset button on the motherboard, and then release the reset button after 10 seconds of power on to restore the factory settings
3. Download the ConfigTool tool from Dahua official website, select the camera in the password reset option, export the XML file and send it to the dealer to unlock it
Configuring Audio Settings on Dahua DVRs
Setting up audio on your Dahua DVR is a simple process that can be done by accessing the DVR’s web interface using the correct username and password. Once logged in, navigate to the “Audio” or “Audio & Video” menu, and enable the audio function if it is not already enabled. Select the audio input source, which could be a microphone or audio line-in, and adjust the audio settings as required, including volume and audio quality. Finally, save the changes and exit the menu to complete the audio setup on your Dahua DVR.
If you’re trying to set up your Dahua DVR, keep in mind that the process may vary depending on your device’s specific model and firmware version. For additional guidance, it’s recommended that you refer to your manual or contact us for more information.
How to enable Audio Recording on Dahua camera?
Download the “ConfigTool” IP search tool from Google on the computer. After searching the IP address of the camera, enter the IP address of the camera and the password of the camera in the computer browser to enter the camera menu.
In the audio option, the audio of the main stream and the auxiliary stream Just turn on the function and save it. You need to select the correct microphone. For example, if you use the camera’s built-in microphone, select MIC.
If you choose an external microphone, select Linein. If the camera is connected to a Dahua NVR, you can directly enable the camera’s audio function in the NVR operation.
If you still don’t understand, please feel free to contact us, thank you!
thank you, thanks for your help I was able to fix it myself